2007-2017 JEEP Wrangler JK Fiberglass A69 Heat Extractor Hood

Experience the ultimate upgrade for your 2007-2017 Jeep Wrangler with the A69 Heat Extractor Fiberglass Hood, a product that embodies our unwavering commitment to high-quality materials and impeccable craftsmanship. This unique hood not only transforms your vehicle's appearance with its striking design but also delivers significant performance enhancements, allowing for improved airflow that effectively reduces heat buildup under the hood. This means enhanced engine efficiency, giving you the power and performance you crave. Embrace the excitement of driving a Jeep that truly reflects your passion for performance and style! Our dedicated customer support team is here to assist you with any customization ideas or questions you may have about the A69 Heat Extractor Hood, ensuring that your upgrade is tailored to your unique vision. Dont miss the chance to elevate your ridemake your Jeep a true masterpiece!

FEATURES:
Fully Functional Heat Extraction
Cool Air Enters Open Front Air Scoops and Directs To Engine Compartment
Hot Air Exits From Two Open Heat Extractor Vents
Show Quality Finish
Hand Laid Fiberglass
Smooth Gel Coat Finished Both on Top and Bottom Sides
Reinforced Metal Latch & Hinge Plate For Additional Safety
Stainless Heat Extractor Vents
Direct Bolt-on Using OEM Hardware
Approximate Weight: 30 Pounds

MPN TF50120-A69

WARNING: California Proposition 65: This product can expose you to chemicals including Styrene, which is known to the State of California to cause cancer, and Bisphenol A which is known to the State of California to cause birth defects or other reproductive harm. Click on the link below for more information.

Important When Receiving Freight: upon receiving the product(s) please be sure to inspect the item(s) for "freight damage". If there are signs of freight damage you must refuse the item due to damage then contact us immediately. Make sure to open and inspect all content(s) before signing [this includes removing the wrapping bubbles and plastics to physically inspect the item(s)]. This process usually takes about 5-10 minutes. It is the customer's responsibility to inspect the item thoroughly. If a customer fails to fully open up the box(es) and inspect their merchandise for damage, and signs the freight carrier's paperwork indicating that all merchandise was inspected (which is what is stated on all freight carriers paperwork), inspects their merchandise after the freight carrier leaves and then finds damage, or what is called "concealed damage", neither the freight carrier, nor BMC Extreme Customs will be responsible to replace or pay for repairs to the product.

CargoEdge Insurance Coverage
Due to the size of the hood, they are vulnerable to getting damaged. It’s a common mistake to confuse freight insurance with the liability insurance provided by carriers and freight forwarders. They are not the same at all. Typical carrier or forwarder liability is limited, in some cases to no more than $5.00 per lb of stolen, lost, or damaged cargo, and coverage contains many exclusions. For a typical hood which weighs less than 50lbs, that's only $250 plus freight. CargoEdge Insurance is powered and backed by UPS Capital and adds a piece of mind should your order arrive damaged or stolen.

*DISCLAIMER: All aftermarket hoods sold are either for show or off-road use only. Professional installation & Hood pins are required! The buyer assumes the entire risk as to the quality of the aftermarket parts. In the event such parts prove defective following the purchase and installation, the buyer assumes the entire costs of any necessary servicing, repair, or replacement.

Note: This is not a simple bolt on. We want all consumers to know that there will always be sanding, shaving, cutting, and/or filling prior to installing aftermarket parts. Also, the black primer finish must be sanded and other prep work will be required prior to painting. Some adjustments may be required to properly fit the hood. It is recommended that you oversize the four holes where the hinges join together. This will allow you to adjust your hood height and front to back spacing. Further adjusting of the fender alignment to hood can be accomplished by loosening the screws that hold the fender to the inner wheel well, and if necessary to place the shims or washers between the fender lip and inner fender well to adjust gap.